Backups with AMANDA: Difference between revisions

From Research
Jump to navigation Jump to search
Line 98: Line 98:
  # |                                    |
  # |                                    |
   
   
  trainwreck.shaw.ca                      amanda  ''(again, use '''your''' server)''
  '''trainwreck.shaw.ca'''                     amanda  ''(again, use '''your''' server)''

Revision as of 18:47, 15 April 2007

Restore Files From Amanda

Background


We have two main file-servers (musashi, and yamato), which each perform their own backups Monday through Friday (typically). Musashi has a SCSI-attached HP LTO-1 Ultrium 230 (Aug. 2003) tape-drive; yamato has a replacement Ultrium 232 (Nov. 2006) tape-drive.
Yamato only backs up it's SCSI-connected RAID drives. Musashi doesn't back up one of it's own SCSI-connected RAID drives (too much non-essential data), but musashi does "reach out" and backup other machines' files. What gets backed up is listed/controlled in the /etc/amanda/Dailyxxx/disklist. Both yamato and musashi have amanda configured as a server and client, while the remote machines captured by musashi have amanda configured as a client-only.

Amanda Server Configuration


The first step was to determine the tapetype entry, in /etc/amanda/Dailyxxx/amanda.conf; here are the results from two different tests on separate systems:

Ultrium 230

define tapetype Ultrium230 {
    comment "HP Ultrium 230, produced by amtapetype"
    length 101376 mbytes
    filemark 0 kbytes
    speed 13871 kps
}

Ultrium 232

amanda@trainwreck ~ $ amtapetype -f /dev/nst0 -e 100G -o
Writing 1024 Mbyte   compresseable data:  37 sec
Writing 1024 Mbyte uncompresseable data:  72 sec
WARNING: Tape drive has hardware compression enabled
Estimated time to write 2 * 102400 Mbyte: 14400 sec = 4 h 0 min
wrote 3080192 32Kb blocks in 94 files in 7025 seconds (short write)
wrote 3096576 32Kb blocks in 189 files in 7511 seconds (short write)
define tapetype unknown-tapetype {
    comment "just produced by tapetype prog (hardware compression on)"
    length 96512 mbytes
    filemark 0 kbytes
    speed 13611 kps
}

Tape Drive Compression


Compression can be turned on or off using the mt tool noted below, then initiating the tapetype check; kill the tapetype check with ctrl-C when you've got enough info (takes quite a few minutes)

trainwreck ~ # mt -f /dev/nst0 defcompression 1
trainwreck ~ # su - amanda
amanda@trainwreck ~ $ amtapetype -f /dev/nst0 -e 100G -o
Writing 1024 Mbyte   compresseable data:  42 sec
Writing 1024 Mbyte uncompresseable data:  72 sec
WARNING: Tape drive has hardware compression enabled
Estimated time to write 2 * 102400 Mbyte: 14400 sec = 4 h 0 min

amanda@trainwreck ~ $ logout
trainwreck ~ # mt -f /dev/nst0 defcompression 0
trainwreck ~ # su - amanda
amanda@trainwreck ~ $ amtapetype -f /dev/nst0 -e 100G -o
Writing 512 Mbyte   compresseable data:  38 sec
Writing 512 Mbyte uncompresseable data:  39 sec
Estimated time to write 2 * 102400 Mbyte: 15600 sec = 4 h 20 min


Amanda Client Configuration


Unfortunately, with the Gentoo packaging, you get more than you need, for just a client:

inferno / # emerge -pv amanda

These are the packages that would be merged, in order:

Calculating dependencies... done!
[ebuild  N    ] sys-block/mtx-1.2.18  164 kB 
[ebuild  N    ] sci-visualization/gnuplot-4.0-r1  USE="emacs gd png readline -X -doc -ggi -pdf -plotutils (-svga) -xemacs" 2,111 kB 
[ebuild  N    ] app-arch/mt-st-0.7-r1  35 kB 
[ebuild  N    ] sys-apps/xinetd-2.3.14  USE="perl tcpd" 295 kB 
[ebuild  N    ] app-arch/dump-0.4.41  USE="readline -ermt -static" 277 kB 
[ebuild  N    ] app-backup/amanda-2.4.5  USE="-berkdb -debug -gdbm -samba -xfs" 1,506 kB 

Total: 6 packages (6 new), Size of downloads: 4,386 kB

There are a couple of separate steps required, for amanda-client to work - configuring the xinetd meta-server, and configuring amanda. Most aggravations seem to stem from permissions, whether it's the server-access through xinetd, or the amanda-permitted-user in .amandahosts.

inferno / # emacs -nw /etc/xinetd.d/amanda

service amanda
{
        socket_type     = dgram
        protocol        = udp
        wait            = yes
        user            = amanda
        group           = amanda
        groups          = yes
        server          = /usr/libexec/amandad
        # You need to ensure this points to your Amanda server!
        # Don't just remove it!
        only_from           = trainwreck (clearly, this should point to your server)
        disable         = no
}


inferno / # emacs -nw /etc/amanda/amandahosts

# Machine-name for those hosts which are permitted to back up (fully-qualified
# is best).  An entry in /etc/hosts adds fail-safe against DNS death :-)
# |
# |                                     permitted user-name
# |                                     |

trainwreck.shaw.ca                      amanda  (again, use your server)